After a few weeks’ break for the holidays with family and friends, we return to UtPåTur’s yard on a very chilly morning. It is minus 5 degrees, the deck is a true skating rink, and we actually have to breathe on the padlock and the door just to get them open!


UtPåTur awakens in her icy chrysalis…

During the first few weeks of work, we had dismantled everything and found new catastrophes daily… so now we are hoping to focus on repairing and reassembling the boat before the launch. Optimism? Or naivety…

January 6 to 20: Still in the thick of the work…

Let’s start with our propulsion saga. We had to replace almost the entire system following, among other things, our broken set screw issue. We finally have all the pieces of the puzzle: a new coupler, a new propeller shaft equipped with a key (a critical part missing from the previous assembly), a new stuffing box, and a cutlass bearing already in stock on board. The first step is to force-fit this bearing into the stern tube. Done! It went in with a mallet in barely 10 minutes—easy! But the moment we slide the shaft inside, it is way too loose… the shaft is swimming in the bearing, which had likely hardened and shrunk with age. Bad start. We have to order a new cutlass bearing and remove the one we have just firmly wedged into the stern tube. That takes over two hours of tinkering with a DIY extractor made of threaded rod and big washers, then banging and pulling to get our brand-new bearing back out.

The easy part: pushing the cutlass bearing into the stern tube…

Brand new propeller shaft in place!

Fortunately, once the new bearing in hand, no further obstacles stand in our way, and with the yard folks’ help, we reassemble UtPåTur’s entire mechanical propulsion, from the transmission seal right down to the propeller anode!

Other major repairs included welding work on the centreboard and hull. We had identified some worrying corrosion spots when we bought the boat and had planned to fill them back up. We were directed to Alan, who works in the next town over and is an expert with aluminium boats. He takes the centreboard to his workshop to fix it, then comes aboard to handle the spots on the hull. 15 minutes later, the hull looks brand new! It’s incredible how well welded aluminium looks.

The corrosion spots were quite deep actually, it was a good idea to weld them shut!

We are very happy to finally have our boat repaired. To celebrate, we decide to use the few rain-free hours left in the day to service a mast winch. And that’s when, to our utter surprise, we find the starboard granny bar simply snapped in two… one of the welds had failed! Doubtless already cracked, the recent cold snap must have been fatal. And of course, UtPåTur reveals this two hours after the welder has left… this boat is definitely a tease…

Unbelievable but true, the weld broke while on the dry without anyone touching it…

Between these major jobs (and the endless downpours drowning Brittany this January), we finish up some odds and ends. The centreboard painting in done on the only (nearly-)sunny day, using a hairdryer to speed up drying times between paint coats. We also have to change a part on the windvane steering that had a tolerance defect (a pin kept falling out), service all the winches and the windlass, trim a water heater hose that was cracking, change the watermaker gauge, and so on.

Hair dryer work to speed up the process and finish all the layers before the rain…

Winch maintenance: cleaning and greasing the gears

We also spend a lot of time (and a significant budget…) shopping, to finalize our spare parts inventory. Where we are going there is nothing, so we need to be able to fix things ourselves. As the singer-sailor Antoine puts it so well: a boat is an object with a stable state called “broken,” which, through much effort and equipment, can be brought to an unstable state called “working”! So we analyse every system: Is it critical? Can we live without it or in “degraded mode”? How might it break, and can we patch it up enough to reach the next port, potentially months away? That’s how we end up with numerous engine parts, hydraulic hoses, Dyneema, turnbuckles to patch a shroud, emergency pumps, antennas, fuses, and pipes…

After the boat, the crew also undergoes an “inspection / spare parts” review: dentist appointments, vaccinations, and pharmacy shopping. Laure brought back a long list of medications from her medical training, which we adapt to our needs. To stay organized, we sort them: a small, very accessible emergency kit (tourniquet, haemostatic sponge, pulse oximeter, fast-acting painkillers…), and the rest in labelled plastic pouches (burns, infections, antibiotics, pain…). We even have what we need to stitch a deep wound or stabilize a fracture… In short, a lot of gear we hope never to have to dig out of its hiding place!

Sorting and organizing the ship’s pharmacy

Despite everything, the pace is a bit less intense than in December and we take “time  off” to visit our friends. A trip to Brest to see the Salamansa crew, another to Nantes to see the Dibonas. While discussing our work list, the latter offers to come help us reinstall the centreboard. The Anouhés had also promised to help. Since these two crews know each other, it is the perfect opportunity for a “Centreboard Party”!

The reunion takes place on a grey but dry afternoon (so, a beautiful day!) in the mud of UtPåTur’s yard. With six of us, handling the board is child’s play… The real challenge begins when we have to fit the board into the boat, sliding precisely between the front and rear edges of the casing. It has to go in at a very precise angle… which isn’t possible with the boat blocked up at its current height. A failure? That would be underestimating the willpower of our three crews! A solution is quickly found: just dig! (Turns out the mud has its perks…) Down into a 20cm trench, the board can be lifted off the ground, and with four people pushing from below and two pulling from above, it quickly finds its place. The pin goes in easily, the board goes up and down; all that is left is to fill in the hole and have a very (very!) good evening together. Thanks again, you guys are awesome!

The photo journal of the reassembly of the centreboard

January 21 to 30: Putting the boat back together

Now that the prop shaft and centreboard are back on, we can get busy rebuilding the boat’s interior. It’s just like a giant Lego, made easier by the step-by-step pictures taken when we pulled her apart.…

First, we have to seal the axis and the centreboard trunk. Two cartridges of silicone and 74 bolts later, UtPåTur is watertight again! At least in theory—the real test will be the launch… Once the trunk is closed, we can—finally—put the table back up. On the engine side, we reinstall the battery and the aft cabin door. Suddenly, the boat looks like our home again!

First step, shutting the centreboard trunk

Now that the interior work is done, we can move back in! In addition to all the gear we offloaded in the fall, we have to stow our recent purchases… UtPåTur swallows it all without flinching. It takes a huge cleaning effort (the boat is suffering from the extreme humidity this winter) and much Tetris-like organization, but what a joy to be done with the heavy construction work! We even host our friend Philippe for lunch (from the catamaran Aumadatroi, whom we met during our Atlantic tour 15 years ago).

Only our starboard granny bar remains broken. But Super Alan comes back to see us at the height of Storm Ingrid and fixes it in less than 10 minutes between two violent squalls. Perfect, this time the boat is starting to look top-notch.

It really is the home stretch of this technical stopover. We load our last belongings, sort the charts and nautical guides we want to take, pick up our mainsail from our sailmaker friend, and rig it directly onto the boom. One last trip to Accastimer, our favourite second-hand shop, and the inventory is almost complete.

The launch is approaching and with no risk of frost in sight, we decide to recommission the freshwater system. As expected, there are a few small leaks where we worked this winter (the sink tap and heater expansion tank), but we have time to fix all that calmly. The engine starts up too; this time, we are ready…

First dinner on board! We start dreaming… one day we will leave Hennebont!

January 31 – February 2: The Launch

Ready, except for one last detail: the rudder is still not back on because we are stored up too low. But it is all planned! Friday evening, Yann comes to get UtPåTur with his tractor and we spend the weekend on the trailer with exactly the height needed to insert the rudder stock into the tube. The operation is quite easy, and after two hours the boat has its steering back!

These last two days of work on the trailer— exact symmetrical to the first two when we stripped UtPåTur of her appendages—are most pleasant. Best of all, we can finally fully move back on board; what a joy to be home!

And there you go, the rudder is back in its place, this time the puzzle is finished!

We hose down the boat to wash off all the mud and moss accumulated during three months on the hard! Indeed, icing on the cake, the weather is relatively nice for this first weekend of February (between squalls, that is to say), perfect for doing the final antifouling touch-ups and rigging the deck. One last glance at the list—yes, yes, everything is crossed off… we even have time for a walk along the Blavet river, which is high and torrent-like, charged with all the rain from recent weeks.

Louisiana bayou? No, Blavet in Morbihan!

Mimosas in bloom in the beautiful evening light

Monday, the last day at the Billie Marine yard. We’re starting to know the team well, especially Charlotte, Yann and Éric—always accommodating and smiling—but we also meet other sailors in the middle of refits. Most notably, (another) Yann and Victoire leaving for Greenland on a sistership of Joshua, Bernard Moitessier’s boat! A superb project; it’s a shame we met so shortly before our launch…

Last meters on mother land…

Indeed the tractor is already humming and, under torrential rain, taking UtPåTur toward the Blavet… The hull touches the water and we rush to check the various through-hulls…  centreboard pin? Dry… Stuffing box? Dry… Seacocks? Dry… Engine? Starts… Clutch? Engages… Nothing holds us to land anymore; a signal to Yann, and he pushes us off the trailer into the river!

Oh, we don’t go far that evening! It is already late, so we take the pontoon 20m from the slipway for the night. But that’s it, we are floating!  Well, only for a few hours; UtPåTur will settle in the mud at low tide—she is a centerboarder after all…

Water above, water under !

February 3: Hennebont – Lorient (8 NM)

First evening on the water, by the stove!

After an evening spent by the stove listening to the rain’s continuous hammering of the deck, we wake up under a big blue sky! A strange but pleasant sensation! Another piece of good news: the boat still seems watertight— although not dry due to pervasive condensation…

We take advantage of the good weather and the river’s shelter to hoist our foresails and finish preparing the deck. That’s it, UtPåTur is all ready to go back to sea!

Sails are set! We just need a little more water and we can set off…

3:30 PM: there is enough water to lower the centreboard a bit and leave at slack water (meaning at the peak of the flood, which just about cancels out the river current!) Goodbye Hennebont, thank you for sheltering us during this long winter refit!

Hooray, we’re sailing! In sunglasses!!

And we are off down the river, under the sun and facing a very moderate southerly wind. How lucky to have this “mouse hole” of calm between the massive low-pressure systems blowing constantly this winter! The engine runs well, the propeller doesn’t vibrate; we can gradually relax.

Soon Lorient is in sight; we head for the port of Kernevel, which we increasingly consider our de facto home port given the time we spent there last year. The harbour master’s staff recognizes us and, helpful as always, comes out in a zodiac to show us our spot. Thanks to them for sharing the only squall of the day with us right in the middle of the docking manoeuvre!

And there we go, we are back at our base camp, the place where our stories with UtPåTur begin! And as soon as the wind isn’t blowing too hard, we’ll be off again immediately!

We’re ready to embark on new adventures!

 PDF

Leave a Reply

Are you human? Please solve:Captcha